316Ti Stainless Steel Strip, Coil & Sheet
UNS: S31635
EN-DIN: 1.4571
products & materials
UNS S31635 Stainless Steel Strip, Coil & Sheet
- ASME SA-240
- ASTM A240
Our wide capabilities give us a unique ability to supply all of your 316Ti stainless steel strip, coil, and sheet needs.
description
316Ti Stainless Steel Alloy Description:
Type 316Ti is a titanium stabilized version of Type 316 molybdenum-bearing austenitic stainless steel. The Type 316 alloys are more resistant to general corrosion and pitting/crevice corrosion than the conventional chromium-nickel austenitic stainless steels such as Type 304. They also offer higher creep, stress-rupture and tensile strength at elevated temperature. Type 316 stainless steel can be susceptible to sensitization – the formation of grain boundary chromium carbides at temperatures between approximately 900 and 1500 °F (425 to 815 °C) – which can result in rapid corrosion. Resistance to sensitization is achieved in Type 316Ti with titanium additions to stabilize the structure against chromium carbide precipitation, which is the source of sensitization. This stabilization is achieved by an intermediate temperature heat treatment, during which the titanium reacts with carbon to form titanium carbides. This significantly reduces susceptibility to sensitization in service by limiting the formation of chromium carbides. Thus, the alloy can be used for extended periods at elevated temperatures without compromising its corrosion resistance.
applications
316Ti Stainless Steel Alloy Uses & Applications:
End Uses:
- Petrochemical
- Chimney liners
- Electrical Hardware
- Acidic environments
Nominal Composition
| C | Mn | P | S | Si | Cr | Ni | Mo | Ti | N | Fe | |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MIN | – | – | – | – | – | 16.0 | 10.0 | 2.00 | 5X(C+N) | – | – |
| MAX | 0.080 | 2.0 | 0.045 | 0.030 | 0.75 | 18.0 | 14.0 | 3.00 | 0.70 | 0.10 | BAL |
Physical Properties
| At 70°F | At 20°C | |
|---|---|---|
| Density | 0.29 lb./in³ | 7.99 g/cm³ |
| Modulus of Elasticity (E) | 28.0 x 10³ ksi | 193 x 10³MPa |
| Coefficient of Expansion | 9.2 x 10⁻⁶ microinches/in.-°F (32-212°F) | 16.5 μm/m-°C (0-100°C) |
| Electrical Resistivity | 28.4 μ ohm.in | 72 μ ohm.cm |
| Thermal Conductivity | 8.4 Btu-in./ft.²hr.-°F (100°C) | 14.6 W/m-K (100°C) |
Typical Room Temperature Mechanical Properties
Typical Mechanical Properties
Typical mechanical properties are based on AK source, ASTM A240.
| Condition | Tensile Strength Min (UTS) | 0.2% YS Min | Elongation% in 2” Min (50.8 mm) | Hardness Rockwell |
|---|---|---|---|---|
| Annealed | 90 ksi (620 MPa) | 36 ksi (248 MPa) | 54% | 76 HRBW |
Limitation of Liability and Disclaimer of Warranty:
- The content in these data sheets is provided primarily by third-party melting mills and is provided for reference only. It is not intended for engineering or design.
- Applications may be discussed, however, Combined Metals Company, LLC, does not recommend or endorse any material for any particular end use or application.
- The data included in this data sheet are typical values and may vary.
- Combined Metals Company, LLC, makes no representations or warranties, express or implied, as to the accuracy, completeness, condition, suitability, performance, fitness for a particular purpose, or merchantability of any information contained in any data sheet.
In no event will Combined Metals Company, LLC, be liable for any damages whatsoever arising from the use of the information included in the data sheets.
Combined Metals: Who We Are
Combined Metals Company (formerly Combined Metals of Chicago ) processes and distributes over 75 alloys of precision strip and wire. Our precision rolling mills, drawing mills, and extensive network of independent North American service centers, support thousands of customers in many industries including Aerospace, Automotive, Chemical, Consumer, Defense, Electronics, Medical, Oil/Gas, and Power Generation, worldwide.
HELPFUL TOOLS
Coil Calculator
Choose a calculator to find coil weights, coil OD’s, coil footage, and PIW.
PIW & Footage
Weight & Footage
Weight & PIW
